top of page

Tips and Advice for Doors and Windows

Silicone or Weatherstripping: Which Should You Choose?

Sep 20
6 min read
Silicone or weatherstipping, which should you choose?

A door that lets in a slight draft or a window that feels cold to the touch does not necessarily need to be replaced. The real question is often: silicone or weatherstripping? Both solutions improve airtightness, but they do not address the same problem. Using the wrong product can leave the air leak unresolved, interfere with the operation of the door or window, or create a repair that is difficult to correct later.

To make the right choice, first determine where the air, water, or cold is getting in. Silicone is used to seal a fixed joint. Weatherstripping, on the other hand, creates a tight seal between two moving components, such as a door and its frame. Understanding this simple distinction can often prevent unnecessary expenses and help extend the life of your existing components.

Silicone or Weatherstripping: Two Very Different Roles

Silicone is a caulking product. Once applied and cured, it forms a flexible, waterproof barrier in an area that is not intended to move significantly. It is particularly useful around certain exterior joints, between a frame and siding, or wherever two fixed materials meet.

Weatherstripping is a compressible component made of rubber, vinyl, foam, or a similar material. It is designed to compress each time a door or window closes and return to its original shape when it opens. Its purpose is to block drafts, dust, moisture, and sometimes noise without interfering with the normal operation of the opening.

In other words, silicone cannot replace worn weatherstripping around an entrance door or patio door. Likewise, adding weatherstripping over a crack in a fixed exterior joint will not provide a lasting solution. Each product has its own purpose.

When Silicone Is the Right Solution

Silicone is appropriate when a fixed joint is cracked, separated, shrunken, or missing. Outdoors, these defects can allow water to seep behind certain parts of the frame. Indoors, they may also contribute to the sensation of a draft, although the main source of the problem may sometimes be elsewhere.

A silicone joint in good condition should be continuous, well adhered, and flexible. If it is cracked, crumbling, pulling away from the surfaces, or has gaps at the ends, it should be inspected. However, simply applying a new layer over old silicone is generally not enough. A durable repair usually begins by removing the deteriorated sealant, cleaning the surfaces, and applying a product that is compatible with the existing materials.

Choosing the right product also matters. A quality exterior sealant must withstand temperature fluctuations, UV rays, and moisture. Some silicones do not adhere well to certain surfaces or are difficult to paint. In many situations, a caulking sealant specifically designed for doors and windows is more appropriate than a product chosen simply because it happens to be available in the garage.

Care must also be taken around windows. Some windows have drainage openings designed to direct water toward the exterior. Blocking these openings with silicone can trap moisture and make the problem worse rather than solve it.

Signs That a Fixed Joint Needs Repair

A localized leak near the corner of a frame, signs of moisture after heavy rain, or a visibly open exterior joint are good indicators. Silicone may then be part of the solution.

However, if air enters mainly when the door is closed, or if the problem changes depending on the pressure applied to the handle, the weatherstripping or door adjustment is more likely to be the cause.

When to Replace Weatherstripping

Weatherstripping is one of the first components to inspect when an entrance door, window, or patio door lets air in around its perimeter. Over time, it can become compressed, hard, torn, loose, or lose its elasticity. Even a small damaged section can create a noticeably cold area during a Quebec winter.

Effective weatherstripping should make even contact with the door or window panel when it is closed. If there is a visible gap, you can feel air coming through in a specific area, or the material remains flattened after the opening is released, replacement may be necessary.

A sheet of paper placed between the panel and the frame can provide a useful clue: if it slides out easily when the door or window is closed, there may not be enough compression to create a proper seal.

However, new weatherstripping cannot compensate for a sagging door, a poorly positioned strike plate, worn hinges, or a patio door whose rollers no longer support the panel properly. In these situations, the hardware and alignment should be corrected before or while replacing the weatherstripping. Otherwise, the new material may wear prematurely or make the door more difficult to close.

The Right Weatherstripping Must Match the Existing Profile

There are several types of weatherstripping, including bulb, fin, compression, self-adhesive, and products designed to fit into a groove in the frame. They are not interchangeable.

Weatherstripping that is too thick can put excessive pressure on the handle and make the door difficult to close. A product that is too thin will continue to let air through. Self-adhesive weatherstripping can be useful as a temporary solution in some simple situations, but it rarely provides the same durability or precision as weatherstripping designed specifically for the profile of the door or window.

This is why it is better to identify the existing component, its location, and the cause of its deterioration before purchasing a generic roll of weatherstripping. The best repair is one that respects the normal operation of the door or window.

Common Mistakes to Avoid

The first mistake is applying silicone everywhere you feel air coming in. On a door, this can cause the panel to stick to the frame, interfere with proper closing, or leave an unattractive seal that will eventually need to be removed. Silicone should be used on fixed joints, never on contact areas that need to open and close.

The second mistake is replacing the weatherstripping without checking its compression. If the door rubs along the bottom, catches on the frame, or requires unusual force to lock, the problem may involve more than the seal itself. The hinges, strike plate, threshold, or rollers may need adjustment or repair.

The third mistake is confusing condensation with air or water infiltration. Condensation on the interior surface of a window may be related to the humidity level inside the home. However, condensation between the panes of an insulated glass unit generally indicates that the seal of the glass unit has failed. Neither silicone nor weatherstripping will correct this specific problem.

Finally, do not overlook the bottom of the door. A gap underneath can allow a significant amount of cold air to enter even when the sides are properly sealed. The door sweep, threshold, and alignment should therefore be inspected along with the rest of the perimeter.

How to Identify the Most Cost-Effective Repair

Before applying any product, observe how the door or window behaves during cold or windy weather. Slowly move your hand around the frame, inspect the corners, check whether the weatherstripping makes even contact, and test how the opening closes.

An air leak in the centre of the top of a door may indicate an alignment issue. A leak near an exterior joint may point toward caulking. A patio door that is difficult to slide may have a roller problem that is also affecting its airtightness.

The most cost-effective repair is rarely the one that adds the most material. It is the one that addresses the actual cause: the right sealant for a fixed joint, the right weatherstripping for a moving component, or properly adjusted hardware so everything aligns as it should.

For homeowners on the North Shore, in Laval, or Montreal, a professional inspection can be useful when an air or water leak persists despite an apparent adjustment, when there are signs of water infiltration, or when a door no longer closes properly.

At MMC Portes et Fenêtres, we favour this targeted approach: repair the component that is causing the problem while keeping what is still in good condition.

A properly selected seal does more than improve comfort around a door or window. It can help prevent small airtightness problems from becoming more expensive repairs over time.

Need Help?

Do you feel a draft around a door or window but are unsure whether the problem is caused by silicone, weatherstripping, or the alignment of the opening? A targeted repair starts by identifying the actual source of the air leak.

At MMC Portes et Fenêtres, we can assess the condition of your weatherstripping, the alignment of your doors and windows, and the components that may be affecting their airtightness. Our goal is to repair what needs to be repaired while keeping what is still in good condition.

Request a free estimate to have your door or window assessed in Montreal, Laval, or the North Shore.


Comments

Rated 0 out of 5 stars.
No ratings yet

Add a rating
bottom of page